LMDZ zoom parameters : Différence entre versions
De LMDZPedia
(Page créée avec « The "Z" in LMDZ stands for "Zoom". This is because it is possible to define, instead of a regular longitude-latitude grid, a grid with varying mesh sizes along longitudes... ») |
|||
| (3 révisions intermédiaires par le même utilisateur non affichées) | |||
| Ligne 7 : | Ligne 7 : | ||
* The zoom factor along longitude(x)/latitude(y) directions, ''grossismx'' and ''grossismy''. These ratio represent the ratio between meshes in the zoomed region versus meshes far outside of it. | * The zoom factor along longitude(x)/latitude(y) directions, ''grossismx'' and ''grossismy''. These ratio represent the ratio between meshes in the zoomed region versus meshes far outside of it. | ||
* The fraction of the zoomed region (i.e. relative to the whole planet which is 360° in longitude and 180° in latitude) along longitude (x) and latitude (y), ''dzoomx'' and ''dzoomy''. In practice the extension in longitude and latitude of the zoomed region will thus be of dzoomx*360° in longitude and dzoomy*180° in latitude | * The fraction of the zoomed region (i.e. relative to the whole planet which is 360° in longitude and 180° in latitude) along longitude (x) and latitude (y), ''dzoomx'' and ''dzoomy''. In practice the extension in longitude and latitude of the zoomed region will thus be of dzoomx*360° in longitude and dzoomy*180° in latitude | ||
| − | * The steepness of the mesh transition between the inner zoom and outer meshes, ''taux'' and ''tauy''. Typically one should avoid a too sharp transition; tau ~3 is a typically | + | * The steepness of the mesh transition between the inner zoom and outer meshes, ''taux'' and ''tauy''. Typically one should avoid a too sharp transition; tau ~3 is a typically maximum value if running without nudging; with strong nudging harsher transitions, e.g. tau~8 or even 10 can also work. |
| + | * It is advised to target, by adjusting number of points along longitude and latitude, to have something close to a "square" mesh (i.e. same extension, in degrees, along longitudes and latitudes) in the inner zoomed area. | ||
== Choosing an adequate time step for a zoomed simulation == | == Choosing an adequate time step for a zoomed simulation == | ||
| − | The rule of thumb, starting from a "day_step" value that works for a | + | The rule of thumb, starting from a "day_step" value that works for a given regular (non-zoomed) grid: |
day_step(zoom) ~ day_step(regular)*max(grossismx,grossismy) | day_step(zoom) ~ day_step(regular)*max(grossismx,grossismy) | ||
Version actuelle en date du 10 octobre 2022 à 10:54
The "Z" in LMDZ stands for "Zoom". This is because it is possible to define, instead of a regular longitude-latitude grid, a grid with varying mesh sizes along longitudes and latitudes.
Zoom parameters
In practice one defines a "zoomed region" of interest where the resolution will be highest (and homogeneous), whereas outside this region the resolution will be low (and also homogeneous, apart from a transition region between the two). This is achieved by specifying the following parameters (usually in gcm.def):
- The zoom center coordinates (in degrees), clon and clat
- The zoom factor along longitude(x)/latitude(y) directions, grossismx and grossismy. These ratio represent the ratio between meshes in the zoomed region versus meshes far outside of it.
- The fraction of the zoomed region (i.e. relative to the whole planet which is 360° in longitude and 180° in latitude) along longitude (x) and latitude (y), dzoomx and dzoomy. In practice the extension in longitude and latitude of the zoomed region will thus be of dzoomx*360° in longitude and dzoomy*180° in latitude
- The steepness of the mesh transition between the inner zoom and outer meshes, taux and tauy. Typically one should avoid a too sharp transition; tau ~3 is a typically maximum value if running without nudging; with strong nudging harsher transitions, e.g. tau~8 or even 10 can also work.
- It is advised to target, by adjusting number of points along longitude and latitude, to have something close to a "square" mesh (i.e. same extension, in degrees, along longitudes and latitudes) in the inner zoomed area.
Choosing an adequate time step for a zoomed simulation
The rule of thumb, starting from a "day_step" value that works for a given regular (non-zoomed) grid:
day_step(zoom) ~ day_step(regular)*max(grossismx,grossismy)
It is also advised to check what others users have successfully used, see e.g. LMDZ_zoom_collection
24/11/2021
